The pond is warming up, the filtration is restarting, and the question arises again: where to buy the right UV lamp for your outdoor pond? A pond specialist or a retailer capable of checking your device's reference is a good starting point. The choice must be documented before comparing offers.
On Aquishop, the lamp product pages provide indications of power and compatibility. To order with confidence, prepare the full name of your clarifier or filter, then check the part offered. A search limited to "UV bulb for pond" brings up products that do not all meet the same need.

Where to look: three criteria more useful than a long list of stores
First, choose a product page that clearly identifies the part: power, manufacturer's reference, base, and compatible devices when known. A photo alone does not allow you to confirm a replacement.
Then see if the information matches your version. An old filter and its successor may have similar names without using the same lamp. The purchase date helps guide the search, but the model number remains more precise.
Finally, check the conditions displayed at the time of ordering: availability of the selected variant, contents sold, and stated delivery time. This information can change. A general mention found in an old description does not replace the current status of the product.
This method also works for an in-store purchase. A clear photo of the device's plate prevents you from leaving with a lamp approximately chosen from memory.
Prepare your purchase in ten minutes
Gather four elements in the same folder: the photo of the label, the manual if you have it, a photo of the old lamp, and its legible reference. You can keep this folder for subsequent replacements.
Add the date of the last change and the usual operating period. This information helps distinguish a preventive replacement from a recent failure.
If the device has several lamps, note their number. On some models, the total power results from several tubes. The Bitron C 110 is, for example, associated with two 55 W lamps in the compatibility indications of the OASE part concerned.
In case of doubt, ask for a verification by giving the full model. "I have an OASE filter for a large pond" does not allow you to select a part without the risk of error.
Bulb, quartz, and clarifier: pay attention to the contents sold
| Product searched | Function | To check before purchase |
|---|---|---|
| Replacement UV-C lamp | Consumable electrical element of the device. | Reference, power, base, dimensions, and required quantity. |
| Quartz sleeve | Transparent protection between the lamp and the water on the models concerned. | Compatibility, condition of the seals, and included accessories. |
| Seal or sealing part | Sealing of the assembly provided by the manufacturer. | Position in the exploded view and exact reference. |
| Complete UV clarifier | Device including a chamber and a power supply. | Flow rate, pressure, installation, and suitability for the pond. |
Commercial photos may show a complete device to illustrate a part. Read the title and the contents of the sale. A new lamp does not necessarily include the quartz sleeve, the seals, or the electrical head.
Two examples to guide a search on Aquishop
Do you have an old FiltoClear 11000? The lamp presented for FiltoClear 11000 in 11 W is a lead to compare with the manual of your version. The number appearing in the name of a filter must not be interpreted as the power of its lamp.
For several OASE devices using a 55 W lamp, the reference 56636 has a manufacturer compatibility list. It includes notably the Vitronic 55 and Bitron C 55 concerned. A mercury lamp of the same power is a different verification.

These examples show how to search for a part, without replacing the reading of the nomenclature. If your device is not mentioned or if its suffix differs, have the correspondence confirmed.
Should you buy a lamp every spring?
The beginning of the season is a practical time to inspect the installation. The replacement decision however depends on the accumulated hours and the manufacturer's recommendations.
JBL indicates a duration of use of around 6,000 to 8,000 hours for some UV-C lamps. A lamp used continuously can reach its recommended duration well before a lamp used only part of the year. Other technologies have their own deadlines.
The color visible through an indicator does not measure the remaining germicidal performance. Note the change on the manual or in your maintenance log, and use the indicator only according to the function the manufacturer assigns it.
A lamp bought in advance must remain protected from shocks in a place suitable for its storage. Keep its label and its box: they will be useful for the next order and to transport the used part to the collection.
Take advantage of the purchase to check the necessary maintenance
Before ordering, inspect the accessible parts under the conditions provided by the manual. A calcified quartz sleeve, a deformed seal, or a cracked fitting deserves to be identified before reassembling everything.
For some OASE equipment, a maintenance cleaner such as AquaActiv PumpClean can be provided to remove deposits from the equipment. Respect the indications of the cleaner and the device, then rinse the parts as requested. It is about maintaining a disassembled piece of equipment, not dosing a treatment in the pond.
Do not systematically replace all parts: check their condition and the maintenance instructions. On the other hand, a cracked quartz or a damaged seal must be treated before returning to water.
The new lamp does not solve all green water problems
UV is part of a whole. The water must pass through the chamber at the intended flow rate, then the materials retained by the filtration must be removed during maintenance.
A pump changed for a more powerful model can change the flow rate in the device. An enlarged or more populated pond can also exceed the conditions that had served to select the equipment. In these situations, a simple new bulb does not correct the sizing.
Also observe the nature of the problem. Filaments attached to plants and leaves deposited at the bottom require a different intervention than uniformly green water. For accessible waste, a targeted cleaning with a PondoVac 4 can complete the maintenance, while monitoring the water level and the animals.
Reception and installation: the last checks
- Compare the received reference with the ordered one before disassembling the installation.
- Check the packaging, the base, and the tube without applying stress to the glass.
- Do not mount a part showing a break or a visible defect.
- Unplug the device before opening and follow its replacement procedure.
- Put it back in circulation and check the sealing before powering on the UV, according to the manual.
Never test a lamp lit in the open air. Its radiation must remain confined in the closed and intact device. The opening safety devices must remain functional.
Place the old lamp in a suitable collection. Recupel specifies the collection points for lamps in Belgium and the precautions in case of breakage. The glass of a used lamp does not join the bottles in a glass bubble.
Prepare the restart of the pond
First find the exact model, then compare the lamp, the quartz, and the eventual seals to replace. A well-prepared order facilitates a complete reassembly.
See the lamp for FiltoClear 11000 in 11 W →
See the OASE 55 W lamp, reference 56636 →
Sources
- OASE — Reference 56636: identification and list of compatible devices.
- JBL — UV-C lamps, maintenance and replacement: duration of use and handling.
- JBL — ProCristal UV-C manual: replacement and operating safety.
- Royal Horticultural Society — Pond filters: place of UV and filtration in maintenance.
- Recupel — Lamps: collection and precautions.
- Aquishop product pages of the lamps, PumpClean, and PondoVac 4 mentioned in the guide.











